Micronet-technology SP1659P User Manual

User’s Manual PoE Management Switch Model No.: SP1659P http://www.micronet.info

On the left-top corner, there is a pull-down list for Auto Logout. For the sake of security, we provide auto-logout function to protect you from ille

Tx Central Wavelength : 0 Baud Rate : 1G Vendor OUI : 00:00:00 Vendor Name : TechCOM Vendor PN : PT4

disable qos Syntax: disable qos Description: To disable QoS. Argument: None Possible value: None Example: SP1659P(qos)# disable qos disable tos Synt

enable tos Syntax: enable tos Description: To enable ToS. Argument: None Possible value: None Example: SP1659P(qos)# enable tos set dscp Syntax: se

Argument: <type_value>: Delay Priority: 0; Throughput Priority: 1; Reliability Priority: 2; Monetary Cost

DiffServ Queue DiffServ Queue DiffServ Queue DiffServ Queue ---------- ------- ---------- ------- ---------- ------- ---------- -------

Disable 802.1p Priority Disable ip tos classification Disable ip diffserv classification Sche

Description: To display the current setting status of isolated group. Argument: None Possible value: None Example: SP1659P(security-isolated-group)# s

<<Restricted Group>> set Syntax: set <ingress> <egress> Description: To set up the function of the restricted group. Argument

set Syntax: set get-community <community> set set-community <community> set trap <#> <ip> [port] [community] Description: T

disable Syntax: disable Description: To disable the STP function. Argument: None Possible value: None Example: SP1659P(stp)# disable enable Syntax:

Parameter description: y Model name: The model name of this device. y System description: As it is, this tells what this device is. y Location: T

Example: SP1659P(stp)# set port 1-16 0 128 yes auto set version Syntax: set version <stp|rstp> Description: To set up the version of STP. Argu

22 DISCARDING 2000000 128 No Auto 23 DISCARDING 2000000 128 No Auto 24 DISCARDING 2

show Syntax: show Description: To display the basic information of the switch. Argument: None Possible value: None Example: SP1659P(system)# show Mo

MM: daylight saving start Month (01-12) DD: daylight saving start Day (01-31) HH: daylight saving start Hour (00-23) mm: daylight saving end Month (01

SP1659P(time)# set ntp 210.59.157.10 8 SP1659P(time)# show Syntax: show Description: To show the time configuration, including “Current Time”, “NTP

SP1659P(trunk)# set hash 2 SP1659P(trunk)# set trunk Syntax: set trunk <port-range> <method> <group> <active LACP> Descripti

Example: SP1659P(trunk)# show lacp-detail 2 Aggregator 2 Information: Actor Partner ---

Argument: <vid>: which vlan group you want to delete, available from 1 to 4094 Possible value: <vid>: 1 to 4094 Example: SP1659P(vlan)# de

Example: SP1659P(vlan)# enable drop-untag 5-10 enable svl Syntax: enable svl Description: To enable Shared VLAN Learning. Argument: None Possible val

<pvid>: 1 to 4094 <default_priority>: 0 to 7 Example: SP1659P(vlan)# set pvid 3,5,6-8 5 6 set tag-group Syntax: set tag-group <vid>

y IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click <Apply> button

Member :2 3 4 5 6 13 14 15 Untag : SP1659P(vlan)# show pvid Syntax: show pvid Description: To display pvid, priority and drop untag r

Example: SP1659P(vs)# enable set gid Syntax: set gid <gid> Description: To set the group id. Argument: <gid>:Group ID Possible value: <

5. Specification IEEE Standards IEEE802.3, 10BASE-T IEEE802.3u, 100BASE-TX IEEE802.3ab, 1000BASE-T IEEE802.3z, 1000BASE-SX/LX IEEE802.3x, Flow Co

Key Features Auto Negotiation Auto Uplink Flow Control for full duplex (IEEE802.3x) Link Aggregation Control Protocol (IEEE802.3ad) * Up to 3 g

Parameter description: y Current Time: Show the current time of the system. y Manual: This is the function to adjust the time manually. Filling the

Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31. Default: 1 Hour: Range is 0 ~ 23. Default: 0 3.3.4 Account Configuration In this functio

Parameter description: y Name: A name is composed of any letter (A-Z, a-z) and digit (0-9) with maximal 8 characters. y VID: The switch supports

devices. Parameter description: y State: It is used for the activation or de-activation of VSM. Default is Enable. y Role: The role that the swit

ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed the port

The local port has to be preset its capability. In port 1 – 24, they are supported Fast Ethernet with TP media only, so the result will show 100M/Full

Display the fiber optical transmitting central wavelength, for instance, 850nm, 1310nm, 1550nm and so on. Baud Rate: Display the maximum baud rate of

Table of Content 1. INTRODUCTION... 3 1.

Parameter description: y State: Set the communication capability of the port is enabled or disabled. When enabled, traffic can be transmitted and

Interval is used to set the update frequency. Default update time is 3 seconds. Parameter description: y Tx Byte: Total transmitted bytes. y Rx Byt

Parameter description: y Rx Packets: The counting number of the packet received. y Rx Octets: Total received bytes. y Rx Errors: Number of bad pac

Parameter description: y Vmain: The volt is supplied by the PoE. y Imain: The sum of the current that every port supplies. y Pconsume: The sum of

Parameter description: y Status: Include “Normal” or “Active” two kinds of status. The former means the port is ready to link and supply the power

y SNMP: The term SNMP here is used for the activation or de-activation of SNMP. Default is Enable. y Get/Set/Trap Community: Community name is used

time is 30 sec. If DHCP Broadcasting Suppression function is enabled, the delay time is set randomly, ranging from 0 to 30 seconds, because the exactl

Query message from a router. y IP Address: Show all multicast groups IP addresses that are registered on this device. y VLAN ID: Show VLAN ID for ea

y Symmetric Vlan: This is called Ingress Rule (Rule 1, The Ingress Filtering Rule 1 is “forward only packets with VID matching this port’s configured

y VLAN Name: The name defined by administrator is associated with a VLAN group. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maxi

3.18 BANDWIDTH ...

It bases on 802.1p QoS and affects untagged packets. When the packets enter the switch, it would get the priority precedence according to your Default

3.10 MAC MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static Forward, Static Filter and M

Parameter description: y Aging Time: Delete a MAC address idling for a period of time from the MAC Table, which will not affect static MAC address.

y VID: VLAN identifier. This will be filled only when tagged VLAN is applied. Valid range is 1 ~ 4094. y Queue (Priority): Set up the priority (0~

address and alias name directly. 3.11 GVRP GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automati

y Default Applicant Mode: The mode here means the type of participant. There are two modes, normal participant and non-participant, provided for the

Parameter description: y Received: Total GVRP Packets: Total GVRP BPDU is received by the GVRP application. Invalid GVRP Packets: Number of invalid G

VLAN identifier. When GVRP group creates, each dynamic VLAN group owns its VID. Valid range is 1 ~ 4094. y Member Port: Those are the members belongi

Show the current root bridge priority. y Root Port: Show port number connected to root bridge with the lowest path cost. y Root Path Cost: Show the

Parameter description: y Spanning Tree Protocol: Set 802.1W Rapid STP function Enable / Disable. Default is “Disable” y Bridge Priority: The lower

1. Introduction Micronet SP1659P PoE Management Switch features Power over Ethernet function, which helps user to centralize power distribution and

3.12.3 STP Port Configuration In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disabl

y Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID. Port IDs are often compared in order to d

the bandwidth aggregation. For example, if there are three Fast Ethernet ports aggregated in a logical port, then this logical port has bandwidth thre

Parameter description: y Method: This determines the method a port uses to aggregate with other ports. None: A port does not want to aggregate wit

3.13.2 Aggregator View To display the current port trunk information from the aggregator point of view. Parameter description: y Aggregator: It show

y Key: Show the key value of the aggregator. The key value is determined by the LACP protocol entity and can’t be set through management. y Trunk St

Supplicant: It is an entity being authenticated by an authenticator. It is used to communicate with the Authenticator PAE (Port Access Entity) by ex

The figure as above shows the procedure of 802.1x authentication. There are steps for the login based on 802.1x port access control management. The p

connected is in the unauthorized state, the supplicant and the devices connected to this port won’t be allowed to access the network. 10. When the su

3.14.2 Mode Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Parameter description: y Por

1.3 Physical Description SP1659P front view RESET Button The button provides users to restart the switch. LEDSET Button: It is used to change

The current 802.1X status of the port. In Disable mode, this field is Disabled. y 802.1x with Multihost mode: When selecting 802.1x with Multihost mo

Choose whether regular authentication will take place in this port. Default: ON y reAuthPeriod(1-65535 s): A non-zero number seconds between the peri

Parameter description: These trap functions are as they describe. The special one is Module Swap. It means that when the switch detects a module with

y Username: your username on the mail server. y Password: your password on the mail server. y Email Address 1 – 6: Email address that would like to

y Restore User: Retrieve the previous confirmed working configuration stored in the flash memory to update start configuration. When completing to re

y Mode: Used for the activation or de-activation of Port Mirror function. Default is disabled. y Monitoring Port: Set up the port for monitoring. Va

y Egress: Select the ports that you would like their Restricted Group to set into “Egress” mode. Just tick the check box beside the port x and valid

y Port No.: Choose the port that you would like this function to work on it. Valid range of the port is 1~26. y Rate: Set up the limit of Egress

UNUSED (1bit). User can randomly control these fields to achieve some special QoS goals. When bits D, T, R, or M set, the D bit requests low delay,

Parameter description: y QoS Mode: You can Enable QoS Mode and let QoS function become effective. Default is disabled. y Priority Control: Just t

2. Installation This switch can be placed directly on your desktop, or mounted in a rack. If you install the device in a normal-standalone standar

Queue 3. 3.19.4 D/T/R/M - Type ToS IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how

TOS Monetary Cost Priority Mapping works while M-TYPE in TOS field of IP header of the packets received by the switch is configured. 3.19.5 DSCP I

mapping to Queue 0, Priority 16~31 are mapping to Queue 1, Priority 32~47 are mapping to Queue 0, Priority 48~63 are mapping to Queue 0. 3.20 Dia

is available or not. You can simply fill in a known IP address and then click <Ping> button. After a few seconds later, the switch will report y

y Auto Upload Enable: Switch the enabled or disabled status of the auto upload function. y Upload Log: Upload log data through tftp. y Clear Log: C

3.25 Logout The switch allows you to logout the system to prevent other users from the system without the permission. If you do not logout and exit

4. Text-based User Interface 4.1 Setup the Connection The switch provides other user interface to access by telnet and direct console. The manag

Data bit: 8 Stop bit: 1 Flow control: None Press “Enter” key to begin login screen. Enter the username and password to login the management c

4.2.3 help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this comman

11. ip 12. help 13. ip 14. history SP1659P(ip)# history 3 Command history: 13. ip 14. history 15. history 3 4.2.5 restore default Syntax:

Note: As the switch supports 802.3ad LACP (Link Aggregation Control Protocol) capability which up to 3 groups, to build up switch-to-switch connectivi

Possible value: None. Example: SP1659P# save start Saving start... Save Successfully 4.2.8 save user Syntax: save user Description: Save the curren

<mode>: 0 or 1 Example: SP1659P(802.1x)# set mode 2 1 SP1659P(802.1x)# set port-control Syntax: set port-control <port-range> <author

Syntax: set reAuthMax <port-range> <max> Description: The number of reauthentication attempts that are permitted before the port becomes

Example: SP1659P(802.1x)# set state 192.168.1.115 1812 WinRadius set suppTimeout Syntax: set suppTimeout <port-range> <sec> Description:

Syntax: show parameter Description: To display the parameter settings of each port. Argument: None Possible value: None Example: SP1659P(802.1x)# show

4.3.2 account add Syntax: add <name> Description: To create a new guest user. When you create a new guest user, you must type in password and

4.3.3 alarm <<email>> del mail-address Syntax: del mail-address <#> Description: The Del here is used to remove the configurat

Password : **************** Email Address 1: [email protected] Email Address 2: Email Address 3: Email Address 4: Email Address 5: Email Address

5 Authentication Failure v 6 User Login 7 User Logout 8 STP Topology Changed 9 STP Disabled 10 STP Enabled 11 LACP Disabled 12 LACP

<phone-number>: phone number Possible value: <#>: 1 to 6 Example: SP1659P(alarm-sms)# set server 192.168.1.7 SP1659P(alarm-sms)# set user

3. Web-based User Interface 3.1 Setting up Connection This switch can be managed using a standard Web Browser from any computer attached to the

Example: SP1659P(bandwidth)# set egress-rate 1-16 299 set ingress-rate Syntax: set ingress-rate <range> <data_rate> Description: To setu

13 102400 102400 14 102400 102400 15 102400 102400 16 102400

Possible value: None Example: SP1659P(config-file)# import user-conf Import successful. set export-path Syntax: set export-path <filepath> Des

Example: SP1659P(dhcp-boot)# show Dhcp Boot : Enable Second : 10 4.3.8 diag diag Syntax: diag Description: Diag is used to test whether UART, D

show Syntax: show Description: To display the information of tftp server and upgrade-path. Argument: None Possible value: None Example: SP1659P(firm

GVRP group information Current Dynamic Group Number: 1 VID Member Port ---- -------------------------------------------------- 2 5 SP1659P(gvrp)#

<non-participant>: set applicant as non-participant mode Possible value: <range>: 1 to 24 <normal|non-participant>: normal or non-

set timer Syntax: set timer <range> <join> <leave> <leaveall> Description: To set gvrp join time, leave time, and leaveall t

Total GVRP Packets 0 0 Invalid GVRP Packets 0 ---- LeaveAll message 0 0 JoinEmpty message

Example: SP1659P(igmp-snooping)# show igmp-snooping Snoop Mode: Active SP1659P(igmp-snooping)# show multicast Snoop Mode: Active IP Multicast: 1)

3.2 Web Management Overview After you login, the switch shows you the system information as below. This page is default and tells you the basic inf

<gateway> : 192.168.1.253 or others Example: SP1659P(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 set system IP address : 192.168.1.2

show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log f

SP1659P(mac-table-alias)# set 00-44-33-44-55-44 www show Syntax: show Description: To display the mac alias entry. Argument: None Possible value: Non

Possible value: <#>: 0, 10 to 65535. Example: SP1659P(mac-table-maintain)# set aging 300 SP1659P(mac-table-maintain)# set learning Syntax: se

<<static-mac>> add Syntax: add <mac> <vid> <queue> <rule> <port> Description: To add the static mac entry.

Syntax: Usage: set [<name> <value>] [<vid> <value>] [<ip> <value>] [<port> <value>] [<type> <

Description: To edit management policy record. Argument: [<name> <value>] ACL entry name. [<vid> <value>]

set state Syntax: set state <port-range> <state> Description: To set the PoE state on ports. Argument: <port-range>：which port(s)

10 Normal Enable Normal 0.0 0 0 11 Normal Enable Normal 0.0 0 0 12 Normal Enable Normal 0.0

<range>: 1 to 26 <symmetric | asymmetric>:symmetric or asymmetric Example: SP1659P(port)# set flow-control 3-6 symmetric set speed-duplex